06

OMEX-3000S

In-Line 3-Axis CNC Machining Centre

Aluminium profiles · 8-station quick-change magazine

For industrial aluminium, copper and other light alloys as well as U-PVC profiles. Milling, drilling, chamfering and tapping are completed in one setup. An 8-station quick-change magazine cuts non-cutting time, while a stress-relieved welded bed with imported linear guides, ball screws and rack-and-pinion drives holds accuracy over the long term.

Get a Quote Technical data
OMEX-3000S In-Line 3-Axis CNC Machining Centre

KEY FEATURES

Key features

01

Milling, drilling, chamfering and tapping in one setup, with no re-clamping error

02

8-station quick-change magazine for uninterrupted multi-operation cycles

03

Stress-relieved welded bed for high rigidity and dimensional stability

04

Imported precision guides, screws and servo drives with a 0–18000 rpm high-speed spindle

TECHNICAL DATA

Technical data

Travel & table
X-axis travel3000 mm optional
Y-axis travel350 mm
Z-axis travel350 mm
Accuracy
X positioning accuracy±0.05 mm
Y / Z positioning accuracy±0.02 mm
Repeatability±0.02 mm
Surface roughnessRa 6.3 μm
Feed & spindle
X / Y / Z feed rate50 / 40 / 30 m/min
Spindle speed0 – 18000 rpm
Spindle power9 kW
Machine
Total power13.5 kW
Power supply380 V / 50 Hz
Machine dimensions≈4000 × 1700 × 2500 mm

Specifications are taken from this model's factory technical data sheet. Custom stroke, fixturing and tool magazine configurations are subject to the final technical agreement.

The X-axis travel of every model can be extended to your workpiece length.

CONFIGURATION

Standard configuration

High-speed electric spindle

High-precision linear guides on X/Y/Z

Imported rack and pinion on X, ball screws on Y/Z

8-station quick-change tool magazine

Four pneumatic clamping fixtures

Imported fully digital AC brushless servo drives

Spray cooling and manual pulse generator

Online/offline programming, tool holder Ø2–16 mm (optional ER32)

When supply is short, components from other brands may be used as substitutes, with no difference in quality or grade.

COMPONENT BRANDS

Key component brands

BrandOriginApplication
SYNTECTaiwan, ChinaCNC system / servo motor / drive
PMI / YYCTaiwan, ChinaLinear guide / rack
MaxphotonicsChinaOptional laser source
Schneider / ABBFrance / SwitzerlandLow-voltage electricals

FAQ

Frequently asked questions

The OMEX-3000G suits industrial aluminium, copper and other light alloys as well as U-PVC profiles. The OMEX-A4500 and OMEX-B6500 use BT30 / BT40 spindle tapers and process steel profiles, aluminium profiles, aluminium-wood composites and copper profiles.
Standard X-axis strokes are 3000 mm (OMEX-3000G), 4500 mm (OMEX-A4500) and 6500 mm (OMEX-B6500). Longer workpieces can be handled with extended strokes built to order, evaluated against workpiece length, fixture layout and shop floor conditions.
OMEX-3000G: positioning accuracy X/Y ±0.05 mm, Z ±0.02 mm, repeatability ±0.05 mm. OMEX-A4500: X ±0.05 mm, Y/Z ±0.02 mm, repeatability ±0.01 mm. OMEX-B6500: X ±0.05 mm, Y/Z ±0.02 mm, repeatability ±0.02 mm. The bed is stress-relief annealed and paired with imported linear guides, ball screws and servo systems.
It is optional. With fiber cutting fitted, the OMEX-3000G can first remove most of the allowance by laser as roughing, then switch to precision milling — noticeably faster for complex shaped slots. If you only need milling, drilling, chamfering and tapping, a configuration without the laser can be selected.
Yes. X-axis stroke, table length, fixture type, tool magazine configuration and optional fiber cutting can all be customized to order, confirmed after evaluation against drawings, operations and capacity targets.
Power: 3-phase 380 V / 50 Hz. Air supply: 0.6–0.9 MPa. Ambient temperature 5–40 °C (24-hour average not above 35 °C), relative humidity 30–75%, vibration below 0.5 G. Independent grounding with resistance under 10 Ω.

Other models

REQUEST AN ASSESSMENT

Tell us about your machining conditions

Model of interest：OMEX-3000S · In-Line 3-Axis CNC Machining Centre

  • Workpiece material, section size and length
  • Required operations: milling / drilling / chamfering / tapping / fiber cutting
  • Current machining method, capacity targets and expected delivery

Submitting creates an email draft you can review and edit before sending.

Your email app did not open? Please send directly to: omexlasercnc@gmail.com
  • Hotline：+86 176 5051 3003
  • Email：omexlasercnc@gmail.com
  • WhatsApp / WeChat：+86 176 5051 3003
  • Address：Room 525, Tower B, Country Garden Phoenix Center, 77 Shunyi Road, Shunhua Street, Jinan Area of China (Shandong) Pilot Free Trade Zone
  • Business hours：Mon – Sat, 8:30 – 17:30 (GMT+8)